Before the interview
- Know the seat. Decide whether you are hiring a service tech who runs calls alone, an installer, or an apprentice or helper. The questions below are for service and install techs. For an apprentice, lean on the last two sections.
- Have the phone screen notes in front of you. Follow up on anything that sounded thin. Here are the phone screen questions I use.
- Bring a meter, a capacitor and a photo of a data plate if you can. Handing someone a tool tells you more than any question.
Certification and the basics
"Which EPA Section 608 certification do you hold?"
Technicians who maintain, service, repair or dispose of equipment that could release refrigerant have to be certified under Section 608 of the Clean Air Act, per the EPA. There are four types: Type I for small appliances, Type II for high- and very high-pressure equipment, Type III for low-pressure equipment and Universal for all of them. Most residential split systems fall under Type II.
Good sounds like: a clear type, usually Type II or Universal for a residential service tech, and a card they can show you. Section 608 certification does not expire, per the EPA, so an old card is fine. Watch for: "I work under my lead's card." That is a no for anyone who will handle refrigerant on their own.
"Any other certifications or licenses?"
NATE certification is voluntary, but it shows someone studied past the minimum. Some states and cities also license HVAC contractors or techs, so know what yours requires before you ask.
Technical questions
1. "Walk me through checking the refrigerant charge on a split system."
Good sounds like: they first ask what metering device the system uses. Then superheat for a fixed orifice or piston, or subcooling for a TXV, checked against the manufacturer's numbers from the data plate or charging chart. The system should run long enough to settle first. Watch for: "I add until the pressures look right."
2. "A customer says the AC runs but the house will not cool. Where do you start?"
Good sounds like: a calm order, simple to complex. The thermostat setting, the filter and airflow, whether the outdoor unit is running, the capacitor and contactor, an iced coil, then the charge. The gauges come out late, not first. Watch for: jumping straight to "it needs refrigerant."
3. "How do you test a run capacitor?"
Good sounds like: power off, discharge it safely, meter on capacitance, then compare the reading to the microfarad rating printed on the capacitor and its tolerance. Watch for: skipping the discharge.
4. "A gas furnace tries to light and then locks out. What do you check?"
Good sounds like: read the error code first, then check the flame sensor, the igniter, the pressure switch and the venting. A carbon monoxide check comes before they leave. Watch for: resetting it and calling it fixed.
5. "What changes for you on systems that use A2L refrigerants like R-454B or R-32?"
Newer residential systems are moving to A2L refrigerants, which are mildly flammable. Good sounds like: they have had A2L training or know they need it. They talk about tools and recovery equipment rated for A2L, leak checks, ventilation and following the manufacturer's install instructions. Watch for: "Refrigerant is refrigerant."
6. "How do you size a replacement system?"
Good sounds like: a load calculation, such as ACCA Manual J, plus a look at the ductwork, rather than only matching the tonnage of the old unit. For a service tech who does not sell systems, knowing why the old tonnage can be wrong is enough. Watch for: "Same size as what was there."
Customer and job site questions
- "Tell me about a time a repair cost more than the customer expected. How did you tell them?" Good sounds like: they laid out the options plainly and let the homeowner choose, with no pressure.
- "What does the attic or basement look like when you leave?" Good sounds like: shoe covers, drop cloths, old parts hauled out, and the thermostat set back to where the customer had it.
- "The part is not on the truck. What do you do?" Good sounds like: tell the customer the truth and the next step, call the office, and leave the system safe in the meantime.
Questions about the seat
- "How do you feel about the on-call rotation?" Say how often yours comes around.
- "Why are you leaving, and what would make you stay somewhere five years?"
- "Where do you want to be in two years: lead tech, installs, sales, your own truck?"
Skip anything about age, family, religion, health or where they are from. The never-ask list applies to interviews too.
Score it, then see the work
Rate the answers 1 to 5 on the same scorecard you used on the phone. A strong talker is not always a strong tech. For anyone who scores well, the next step is a paid working interview: a half day riding with your lead tech on real calls.
To be fair
No list of questions catches everything. A nervous tech can blank on a question they could answer in a customer's basement, and someone who memorized the answers can still be slow with a meter. Use the questions to decide who rides along, not who gets hired.
My take
Hire the tech who asks you questions back: which metering device, what the customer already tried, where the data plate is. That habit is the job. If finding enough techs to interview is the hard part, our HVAC recruiting runs the search for you. We write the job post, screen every applicant on your scorecard, run the phone screens and hand you only the cleared candidates. You run the interview.