Before the interview
- Know the seat and the license it needs. Each state sets electrician licensing, and in some places the city or county does. Know what your work requires: a registered apprentice, a journeyman or a master.
- Look the license up. Most states have an online license lookup. Check it before the interview, not after the offer.
- Have the phone screen notes in front of you. Here are the phone screen questions I use.
License and experience
"Which license do you hold, in which state, and how far along are your hours?"
Good sounds like: a clear license level and state, and for an apprentice, their registration and a rough count of hours on the job and in the classroom. Watch for: vague answers, or a license from another state with no plan to qualify in yours.
"What kind of work have you done the most?"
Service, residential new construction, remodels or commercial. Good sounds like: specific jobs that match your work. A great commercial electrician can still be slow on a service call in an occupied home.
Code and technical questions
Most of the country builds to the National Electrical Code, NFPA 70. It is updated every three years, and states and cities adopt each edition on their own schedule. A good answer often starts with "it depends on which edition your area uses," and that is a fine start.
1. "Where does the code call for GFCI protection in a house, and where AFCI?"
Good sounds like: GFCI in the usual wet and damp spots, such as bathrooms, kitchens, garages, outdoors, basements and laundry areas. AFCI in bedrooms and most living areas. A strong answer adds that both lists have grown in recent editions. Watch for: mixing up the two, or not knowing why each exists. A GFCI protects people from shock. An AFCI protects the house from fires started by arcing.
2. "What is the difference between grounding and bonding?"
Good sounds like: grounding connects the system to the earth; bonding ties metal parts together so a fault has a low-resistance path back to the source and the breaker trips. Watch for: using the two words as if they mean the same thing.
3. "A breaker keeps tripping. Walk me through it."
Good sounds like: questions first. When does it trip, what is on the circuit and what kind of breaker is it? Then telling an overload from a short from a ground fault, unplugging loads to isolate it and using a meter instead of guessing. Watch for: "Put in a bigger breaker." That answer alone can end the interview.
4. "How do you choose the wire size for a long run?"
Good sounds like: the load, the conductor's ampacity, the temperature rating of the terminals and the voltage drop over the distance, plus copper versus aluminum. Watch for: one rule of thumb for everything.
5. "Walk me through a panel upgrade, from permit to inspection."
Good sounds like: the permit, a load calculation, coordinating the disconnect with the utility, labeling the circuits, torquing connections to spec and the inspection before the cover goes on for good. Watch for: no mention of the permit.
6. "How do you make sure a circuit is dead before you work on it?"
Good sounds like: shut it off and lock it out, then test with a meter they first checked on a known live source, and check the meter again after. Many electricians call that live, dead, live. Bonus points if they mention arc flash gear and NFPA 70E. OSHA's page on the control of hazardous energy covers the lockout and tagout side. Watch for: "I just flip the breaker." Do not move on until that answer is right.
Questions for an apprentice
- "Are you in a school or a registered program now, and how far along?" Registered programs are listed on Apprenticeship.gov.
- "What tools do you own?" Good sounds like: a real list, and a plan to add to it.
- "What have you done on your own, start to finish?" Good sounds like: honest, small and specific. Pulling wire, mounting boxes, trimming out a room.
- "Why electrical?" Good sounds like: a reason that will last through the first summer in an attic.
Customer and job site questions
- "The homeowner asks you to add an outlet that is not on the work order. What do you do?" Good sounds like: a kind answer, a call to the office, and no side cash jobs.
- "You find something unsafe that is not part of the job. What do you do?" Good sounds like: tell the customer plainly, make it safe if needed, write it down and tell the office.
- "What does the room look like when you leave?" Good sounds like: dust gone, plates on, the panel labeled, and the homeowner shown what changed.
Score it, then see the work
Rate each answer 1 to 5 on the same scorecard you used on the phone screen. For anyone who scores well, the next step is a paid working interview: a half day next to your lead, on work inside the license they hold.
Skip anything about age, family, religion, health or where they are from. The never-ask list applies here too.
To be fair
Code questions reward people who test well, and some excellent electricians do not. A nervous journeyman can freeze on a code section they apply every day. Weigh the troubleshooting and safety answers above the code trivia, and let the working interview settle the rest.
My take
The safety question is the one I would never skip. A journeyman who answers it without thinking and meets the breaker question with questions of their own is worth a working interview, even after a fumbled code section. Need more electricians to interview in the first place? Our electrician recruiting runs the search for you. We write the post, screen every applicant on your scorecard, run the phone screens and hand you only the cleared candidates. You run the interview.